KynSHOT R15015098 Spacer Weight for PCC and AR Hydraulic Buffers

KynSHOT R15015098 Spacer Weight for PCC and AR Hydraulic Buffers

The KynSHOT R15015098 Spacer Weight adds mass and length to compatible KynSHOT hydraulic buffer systems, helping optimize buffer performance and cycling characteristics on PCC and AR platforms. Constructed from stainless steel, this drop-in spacer weight adds 2.5 ounces of mass and 0.75 inches of length to the buffer system while helping prevent buffer tilt during cycling.

Key Features

• Designed for KynSHOT PCC and AR hydraulic buffer systems
• Adds 2.5 ounces of additional buffer mass
• Adds 0.75 inches of length to the buffer system
• Stainless steel construction
• Designed to help prevent buffer tilting during cycling
• Can help reduce felt recoil when properly configured
• Drop-in component for compatible KynSHOT hydraulic buffer setups
• Designed for PCC and AR platforms

Performance and Function

The KynSHOT Spacer Weight was developed in cooperation with Blitzkrieg Components for use with compatible PCC and AR hydraulic buffers. By adding mass in front of the hydraulic buffer, the spacer weight changes the overall buffer system configuration while providing additional weight for cycling dynamics.

The spacer weight adds 0.75 inches of internal length to the buffer system. For setups where full bolt travel and engagement with the bolt catch are required, KynSHOT specifies using an AR-10/A5-length buffer tube, which provides approximately 0.75 inches of additional internal length compared with a standard carbine-length tube.

Recommended Configuration

For many 8- to 16-inch barreled PCC and AR platforms, KynSHOT recommends using the spacer weight in front of an RB5015HD hydraulic buffer with a .308 carbine buffer spring in an AR-10/A5-length buffer tube. This configuration is intended to provide the necessary internal length for full bolt stroke.

If the bolt already has a weight pinned into the rear, KynSHOT recommends leaving that weight installed to retain the full mass of the bolt.

Compatibility

• Designed for compatible KynSHOT PCC hydraulic buffers
• Compatible with applicable KynSHOT AR hydraulic buffer systems
• Designed for PCC and AR platforms

Important Compatibility Note

The additional 0.75 inches of length affects available internal buffer tube travel. If full bolt travel and bolt-catch engagement are required, use an AR-10/A5-length buffer tube as specified by KynSHOT. Verify your complete buffer, spring, tube, and bolt configuration before installation.

Specifications

• Manufacturer: KynSHOT
• Manufacturer Part Number: R15015098
• UPC: 854476005393
• Type: Buffer Spacer Weight
• Material: Stainless Steel
• Color: Silver
• Additional Weight: 2.5 oz.
• Additional Length: 0.75 in.
• Platform: PCC / AR
• Subcategory: Stocks & Buffer Tubes

Frequently Asked Questions

What does the KynSHOT R15015098 Spacer Weight do?

The spacer weight adds 2.5 ounces of mass and 0.75 inches of length to a compatible KynSHOT hydraulic buffer system.

What platforms is the R15015098 designed for?

The R15015098 is designed for compatible KynSHOT hydraulic buffer systems used on PCC and AR platforms.

Does the spacer weight replace the hydraulic buffer?

No. The R15015098 is a spacer weight designed to be used with compatible KynSHOT hydraulic buffers. It adds mass and length to the overall buffer system.

What buffer tube should I use with the spacer weight?

For configurations requiring full bolt stroke and bolt-catch engagement, KynSHOT specifies an AR-10/A5-length buffer tube because it provides the additional internal length required by the spacer weight.

How much weight does the spacer add?

The KynSHOT R15015098 adds 2.5 ounces of weight to the buffer system.

How much length does the spacer add?

The spacer weight adds 0.75 inches of length to the buffer system.

Can I remove an existing weight from my bolt when installing this spacer?

If your bolt has a weight pinned into the rear, KynSHOT recommends leaving it installed to retain the full mass of the bolt.

Is this spacer weight compatible with every AR or PCC buffer system?

No. The R15015098 is intended for compatible KynSHOT PCC and AR hydraulic buffer systems. Verify your buffer and complete operating system configuration before installation.

Optimize your compatible KynSHOT hydraulic buffer system with the R15015098 Spacer Weight. Its stainless steel construction, added 2.5 ounces of mass, and 0.75 inches of additional length provide a purpose-built way to configure compatible PCC and AR buffer systems according to KynSHOT's recommended setup specifications.